Comments on: IBM MTM 2019: Part Three – Challenge #14 https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/?utm_source=rss&utm_medium=rss&utm_campaign=ibm-mtm-2019-part-three-challenge-14 Improving my programming skills step by step. You're invited! Wed, 20 May 2020 17:51:58 +0000 hourly 1 https://wordpress.org/?v=4.9.14 By: kevindurant https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-902 Tue, 31 Dec 2019 12:07:55 +0000 https://kevindurant.be/?p=1433#comment-902 Hi Anonymous

Please see my reply here https://kevindurant.be/ibm-master-the-mainframe-2019/#comment-901

Kind regards,
– Kevin

]]> By: Anonymous https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-889 Tue, 31 Dec 2019 05:26:14 +0000 https://kevindurant.be/?p=1433#comment-889 Hlo kelvin sir,
Today is last day and i m stuck on ch14 of part3 eventhough by doing step by step of instructions i am getting errors like invalid jecl statement, misplaced dd statement and job has no steps….sir plz hlp….

]]> By: Nilay https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-850 Sat, 28 Dec 2019 11:06:08 +0000 https://kevindurant.be/?p=1433#comment-850 Hey, I am getting a 72 line system log as the output. where you have got only few lines of output. Is it ok? or I need to make some changes? please reply

]]> By: Phunsuk Wangdu https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-811 Thu, 26 Dec 2019 07:57:54 +0000 https://kevindurant.be/?p=1433#comment-811 Unknowingly I typed some commands like “ISF754I”, “SYSID SYS1″, ” ISFSYSID”, “ISF766I”. Before typing there commands consecutively ‘Syslog’ was getting appear to the screen but after these commands whenever I type ‘log’, it shows “NO SYS1 SYSLOG FOUND”. Is there any command to reset everything back to normal?

]]> By: kevindurant https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-804 Wed, 25 Dec 2019 16:35:33 +0000 https://kevindurant.be/?p=1433#comment-804 Hi Phunsuk Wangdu

Have you made any changes to the system or a data set during your session? If there was nothing to log then there will be nog logs.

Kind regards,
– Kevin

]]> By: Phunsuk Wangdu https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-800 Wed, 25 Dec 2019 10:27:51 +0000 https://kevindurant.be/?p=1433#comment-800 Namastey Kevin,
Everytime I enter ‘LOG’ as an SDSF command, it says “NO SYS1 SYSLOG FOUND”. Even I deleted my data member once and recreate it but again facing the same issue. Can you resolve it, I’d be greatful.
kind regards,
Phunsuk Wangdu
from India

]]> By: Felipe Fontes https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-735 Thu, 19 Dec 2019 15:53:49 +0000 https://kevindurant.be/?p=1433#comment-735 I know where everybody is getting the error…
it’s ifsysid: s0w1
0 = zero
not o letter

]]> By: Anonymous https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-723 Wed, 18 Dec 2019 12:10:51 +0000 https://kevindurant.be/?p=1433#comment-723 Sir, in output screen only two lines are coming ie, ON TSOINRDR and STARTED……and
Sir give me a proper description about each line or variable that we have to change in rexx code. We did everything that u said…but didn’t worked.

]]> By: kevindurant https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-721 Wed, 18 Dec 2019 08:18:51 +0000 https://kevindurant.be/?p=1433#comment-721 Hi Nomuoja

There should be no need to touch that line. What’s the error message? Did you forget to close a string somewhere?

Kind regards,
– Kevin

]]> By: Nomuoja https://kevindurant.be/2019/12/12/ibm-mtm-2019-part-three-challenge-14/#comment-691 Sat, 14 Dec 2019 23:25:46 +0000 https://kevindurant.be/?p=1433#comment-691 is there no need to touch isfdate on line 10? my error message keeps refering to it

]]>